{"city":"boulder","zip":null,"permits":[{"id":"RFG2026-00898","url":"https://nearbypermits.com/boulder/permit/RFG2026-00898/","address":"2202 Kalmia Ave","addressUrl":"https://nearbypermits.com/boulder/address/2202-kalmia-ave/","zip":"80304","zipUrl":"/boulder/zip/80304/","zipDerived":false,"type":"Roofing","cityType":"Roofing Replacement Permit, Roofing Replacement Permit","status":"Issued","cityStatus":"Issued","description":"All Structures must be permitted separately Total tear-off & reroof of SFD, 38 squares of dimensional shingles on a pitch represented as 5/12. All roof materials shall be installed per manufacturer?s specs. Mid-roof inspection is required if 1) pitch is less than 4/12 or 2) for any roof type other than asphalt shingles (regardless of pitch). Pre-roof inspection required for all overlays. At mid-roof inspection, to ensure the safety and structural integrity of flat-roof buildings within the City of Boulder, a stamped and signed letter from a qualified engineer must be provided. The letter should certify that the installed roof membrane assembly meets all applicable building codes and safety standards, including wind speed verifications, based on an engineering review of the installation. All roof covering materials shall be listed as Class A as tested in accordance with UL Standard 790 or ASTM Standard E 108. At inspection, provide to building inspection staff original wrappers of materials used or applied. Provide additional information -- such as manufacturer's cut sheet for other products used - including, but not limited to, items such as flashing, valley material, sealants, fasteners, ventilation devices or features and roof jacks & penetration boots.","date":"2026-10-07","dateLabel":"Issued","cost":"$35,000","source":"https://services.arcgis.com/ePKBjXrBZ2vEEgWd/arcgis/rest/services/Construction_Permits/FeatureServer/0/query?where=PermitNum%3D%27RFG2026-00898%27&outFields=PermitNum%2COriginalAddress%2COriginalZip%2CPermitType%2CPermitWorkType%2CDescription%2CIssuedDate%2CStatusCurrent%2CEstProjectCost&f=html","group":"exterior","sentence":"All Structures must be permitted separately Total tear-off & reroof of SFD","costValue":35000,"lat":null,"lon":null},{"id":"RFG2026-00896","url":"https://nearbypermits.com/boulder/permit/RFG2026-00896/","address":"137 31st St","addressUrl":"https://nearbypermits.com/boulder/address/137-31st-st/","zip":"80305","zipUrl":"/boulder/zip/80305/","zipDerived":false,"type":"Roofing","cityType":"Roofing Replacement Permit, Roofing Replacement Permit","status":"Issued","cityStatus":"Issued","description":"All Structures must be permitted separately Total tear-off & reroof of SFD, 24 squares of modified bitumen on a pitch represented as 2/12. All roof materials shall be installed per manufacturer?s specs. Mid-roof inspection is required if 1) pitch is less than 4/12 or 2) for any roof type other than asphalt shingles (regardless of pitch). Pre-roof inspection required for all overlays. At mid-roof inspection, to ensure the safety and structural integrity of flat-roof buildings within the City of Boulder, a stamped and signed letter from a qualified engineer must be provided. The letter should certify that the installed roof membrane assembly meets all applicable building codes and safety standards, including wind speed verifications, based on an engineering review of the installation. All roof covering materials shall be listed as Class A as tested in accordance with UL Standard 790 or ASTM Standard E 108. At inspection, provide to building inspection staff original wrappers of materials used or applied. Provide additional information -- such as manufacturer's cut sheet for other products used - including, but not limited to, items such as flashing, valley material, sealants, fasteners, ventilation devices or features and roof jacks & penetration boots. Attention: Wind speed requirements for Flat Membrane Roof Assemblies ? To ensure the safety and structural integrity of buildings within the City of Boulder, the following wind speed verifications are needed for all flat roof membrane assemblies: ? 1.? Engineered Design: A comprehensive engineered design for the flat membrane roof assembly must be submitted at the time of permit application. This design should detail all aspects of the assembly, including materials, installation methods, and load calculations, and number and layout of fasteners to achieve wind speed requirements. ? 2.? Alternative Option: Engineer?s Letter: As an alternative to submitting the full engineered design at the time of permit application, a stamped and signed letter from a qualified engineer will be accepted. This letter must be provided at the time of the mid-roof inspection. The letter should certify that the installed roof membrane assembly meets all applicable building codes and safety standards, based on an engineering review of the installation. Mid-roof inspection still needed to verify class A Fire Rated Assembly. If you have any questions or need further clarification, please contact the City of Boulder Planning and Development Services Dept through Inquire Boulder at https://user.govoutreach.com/boulder/faq.php?cmd=shell.?","date":"2026-10-07","dateLabel":"Issued","cost":"$14,297","source":"https://services.arcgis.com/ePKBjXrBZ2vEEgWd/arcgis/rest/services/Construction_Permits/FeatureServer/0/query?where=PermitNum%3D%27RFG2026-00896%27&outFields=PermitNum%2COriginalAddress%2COriginalZip%2CPermitType%2CPermitWorkType%2CDescription%2CIssuedDate%2CStatusCurrent%2CEstProjectCost&f=html","group":"exterior","sentence":"All Structures must be permitted separately Total tear-off & reroof of SFD","costValue":14296.61,"lat":null,"lon":null},{"id":"RFG2026-00892","url":"https://nearbypermits.com/boulder/permit/RFG2026-00892/","address":"2227 Mapleton Ave","addressUrl":"https://nearbypermits.com/boulder/address/2227-mapleton-ave/","zip":"80304","zipUrl":"/boulder/zip/80304/","zipDerived":false,"type":"Roofing","cityType":"Roofing Replacement Permit, Roofing Replacement Permit","status":"Issued","cityStatus":"Issued","description":"All Structures must be permitted separately Total tear-off & reroof of SFD, 10 squares of dimensional shingles on a pitch represented as 12/12 and 4 squares of base and cap on a pitch represented as 2/12. All roof materials shall be installed per manufacturer?s specs. Mid-roof inspection is required if 1) pitch is less than 4/12 or 2) for any roof type other than asphalt shingles (regardless of pitch). Pre-roof inspection required for all overlays. At mid-roof inspection, to ensure the safety and structural integrity of flat-roof buildings within the City of Boulder, a stamped and signed letter from a qualified engineer must be provided. The letter should certify that the installed roof membrane assembly meets all applicable building codes and safety standards, including wind speed verifications, based on an engineering review of the installation. All roof covering materials shall be listed as Class A as tested in accordance with UL Standard 790 or ASTM Standard E 108. At inspection, provide to building inspection staff original wrappers of materials used or applied. Provide additional information -- such as manufacturer's cut sheet for other products used - including, but not limited to, items such as flashing, valley material, sealants, fasteners, ventilation devices or features and roof jacks & penetration boots. Attention: Wind speed requirements for Flat Membrane Roof Assemblies ? To ensure the safety and structural integrity of buildings within the City of Boulder, the following wind speed verifications are needed for all flat roof membrane assemblies: ? 1.? Engineered Design: A comprehensive engineered design for the flat membrane roof assembly must be submitted at the time of permit application. This design should detail all aspects of the assembly, including materials, installation methods, and load calculations, and number and layout of fasteners to achieve wind speed requirements. ? 2.? Alternative Option: Engineer?s Letter: As an alternative to submitting the full engineered design at the time of permit application, a stamped and signed letter from a qualified engineer will be accepted. This letter must be provided at the time of the mid-roof inspection. The letter should certify that the installed roof membrane assembly meets all applicable building codes and safety standards, based on an engineering review of the installation. Mid-roof inspection still needed to verify class A Fire Rated Assembly. If you have any questions or need further clarification, please contact the City of Boulder Planning and Development Services Dept through Inquire Boulder at https://user.govoutreach.com/boulder/faq.php?cmd=shell.? ?","date":"2026-10-07","dateLabel":"Issued","cost":"$5,600","source":"https://services.arcgis.com/ePKBjXrBZ2vEEgWd/arcgis/rest/services/Construction_Permits/FeatureServer/0/query?where=PermitNum%3D%27RFG2026-00892%27&outFields=PermitNum%2COriginalAddress%2COriginalZip%2CPermitType%2CPermitWorkType%2CDescription%2CIssuedDate%2CStatusCurrent%2CEstProjectCost&f=html","group":"exterior","sentence":"All Structures must be permitted separately Total tear-off & reroof of SFD","costValue":5600,"lat":null,"lon":null},{"id":"RFG2026-00891","url":"https://nearbypermits.com/boulder/permit/RFG2026-00891/","address":"1480 King Ave","addressUrl":"https://nearbypermits.com/boulder/address/1480-king-ave/","zip":"80302","zipUrl":"/boulder/zip/80302/","zipDerived":false,"type":"Roofing","cityType":"Roofing Replacement Permit, Roofing Replacement Permit","status":"Issued","cityStatus":"Issued","description":"All Structures must be permitted separately Total tear-off & reroof of SFD, 29 squares of dimensional shingles on a pitch represented as 5/12. All roof materials shall be installed per manufacturer?s specs. Mid-roof inspection is required if 1) pitch is less than 4/12 or 2) for any roof type other than asphalt shingles (regardless of pitch). Pre-roof inspection required for all overlays. At mid-roof inspection, to ensure the safety and structural integrity of flat-roof buildings within the City of Boulder, a stamped and signed letter from a qualified engineer must be provided. The letter should certify that the installed roof membrane assembly meets all applicable building codes and safety standards, including wind speed verifications, based on an engineering review of the installation. All roof covering materials shall be listed as Class A as tested in accordance with UL Standard 790 or ASTM Standard E 108. At inspection, provide to building inspection staff original wrappers of materials used or applied. Provide additional information -- such as manufacturer's cut sheet for other products used - including, but not limited to, items such as flashing, valley material, sealants, fasteners, ventilation devices or features and roof jacks & penetration boots.","date":"2026-10-07","dateLabel":"Issued","cost":"$24,500","source":"https://services.arcgis.com/ePKBjXrBZ2vEEgWd/arcgis/rest/services/Construction_Permits/FeatureServer/0/query?where=PermitNum%3D%27RFG2026-00891%27&outFields=PermitNum%2COriginalAddress%2COriginalZip%2CPermitType%2CPermitWorkType%2CDescription%2CIssuedDate%2CStatusCurrent%2CEstProjectCost&f=html","group":"exterior","sentence":"All Structures must be permitted separately Total tear-off & reroof of SFD","costValue":24500,"lat":null,"lon":null},{"id":"RFG2026-00888","url":"https://nearbypermits.com/boulder/permit/RFG2026-00888/","address":"175 Manhattan Dr","addressUrl":"https://nearbypermits.com/boulder/address/175-manhattan-dr/","zip":"80303","zipUrl":"/boulder/zip/80303/","zipDerived":false,"type":"Roofing","cityType":"Roofing Replacement Permit, Roofing Replacement Permit","status":"Issued","cityStatus":"Issued","description":"All Structures must be permitted separately Total tear-off & reroof of SFD, 23 squares of dimensional shingles on a pitch represented as 4/12 and 2 squares of modified bitumen on an attached porch on a pitch represented as 2/12. All roof materials shall be installed per manufacturer?s specs. Mid-roof inspection is required if 1) pitch is less than 4/12 or 2) for any roof type other than asphalt shingles (regardless of pitch). Pre-roof inspection required for all overlays. At mid-roof inspection, to ensure the safety and structural integrity of flat-roof buildings within the City of Boulder, a stamped and signed letter from a qualified engineer must be provided. The letter should certify that the installed roof membrane assembly meets all applicable building codes and safety standards, including wind speed verifications, based on an engineering review of the installation. All roof covering materials shall be listed as Class A as tested in accordance with UL Standard 790 or ASTM Standard E 108. At inspection, provide to building inspection staff original wrappers of materials used or applied. Provide additional information -- such as manufacturer's cut sheet for other products used - including, but not limited to, items such as flashing, valley material, sealants, fasteners, ventilation devices or features and roof jacks & penetration boots. ?Attention: Wind speed requirements for Flat Membrane Roof Assemblies ? To ensure the safety and structural integrity of buildings within the City of Boulder, the following wind speed verifications are needed for all flat roof membrane assemblies: ? 1.? Engineered Design: A comprehensive engineered design for the flat membrane roof assembly must be submitted at the time of permit application. This design should detail all aspects of the assembly, including materials, installation methods, and load calculations, and number and layout of fasteners to achieve wind speed requirements. ? 2.? Alternative Option: Engineer?s Letter: As an alternative to submitting the full engineered design at the time of permit application, a stamped and signed letter from a qualified engineer will be accepted. This letter must be provided at the time of the mid-roof inspection. The letter should certify that the installed roof membrane assembly meets all applicable building codes and safety standards, based on an engineering review of the installation. Mid-roof inspection still needed to verify class A Fire Rated Assembly. If you have any questions or need further clarification, please contact the City of Boulder Planning and Development Services Dept through Inquire Boulder at https://user.govoutreach.com/boulder/faq.php?cmd=shell.? ?","date":"2026-10-07","dateLabel":"Issued","cost":"$12,500","source":"https://services.arcgis.com/ePKBjXrBZ2vEEgWd/arcgis/rest/services/Construction_Permits/FeatureServer/0/query?where=PermitNum%3D%27RFG2026-00888%27&outFields=PermitNum%2COriginalAddress%2COriginalZip%2CPermitType%2CPermitWorkType%2CDescription%2CIssuedDate%2CStatusCurrent%2CEstProjectCost&f=html","group":"exterior","sentence":"All Structures must be permitted separately Total tear-off & reroof of SFD","costValue":12500,"lat":null,"lon":null},{"id":"RFG2026-00885","url":"https://nearbypermits.com/boulder/permit/RFG2026-00885/","address":"1625 Lombardy Dr","addressUrl":"https://nearbypermits.com/boulder/address/1625-lombardy-dr/","zip":"80304","zipUrl":"/boulder/zip/80304/","zipDerived":false,"type":"Roofing","cityType":"Roofing Replacement Permit, Roofing Replacement Permit","status":"Issued","cityStatus":"Issued","description":"All Structures must be permitted separately Total tear-off & reroof of SFD,19 squares of dimensional shingles on a pitch represented as 5/12 and 7 squares of dimensional shingle on a pitch represented as 2/12. All roof materials shall be installed per manufacturer?s specs. Mid-roof inspection is required if 1) pitch is less than 4/12 or 2) for any roof type other than asphalt shingles (regardless of pitch). Pre-roof inspection required for all overlays. At mid-roof inspection, to ensure the safety and structural integrity of flat-roof buildings within the City of Boulder, a stamped and signed letter from a qualified engineer must be provided. The letter should certify that the installed roof membrane assembly meets all applicable building codes and safety standards, including wind speed verifications, based on an engineering review of the installation. All roof covering materials shall be listed as Class A as tested in accordance with UL Standard 790 or ASTM Standard E 108. At inspection, provide to building inspection staff original wrappers of materials used or applied. Provide additional information -- such as manufacturer's cut sheet for other products used - including, but not limited to, items such as flashing, valley material, sealants, fasteners, ventilation devices or features and roof jacks & penetration boots. ?Attention: Wind speed requirements for Flat Membrane Roof Assemblies To ensure the safety and structural integrity of buildings within the City of Boulder, the following wind speed verifications are needed for all flat roof membrane assemblies: 1.? Engineered Design: A comprehensive engineered design for the flat membrane roof assembly must be submitted at the time of permit application. This design should detail all aspects of the assembly, including materials, installation methods, and load calculations, and number and layout of fasteners to achieve wind speed requirements. 2.? Alternative Option: Engineer?s Letter: As an alternative to submitting the full engineered design at the time of permit application, a stamped and signed letter from a qualified engineer will be accepted. This letter must be provided at the time of the mid-roof inspection. The letter should certify that the installed roof membrane assembly meets all applicable building codes and safety standards, based on an engineering review of the installation. Mid-roof inspection still needed to verify class A Fire Rated Assembly. If you have any questions or need further clarification, please contact the City of Boulder Planning and Development Services Dept through Inquire Boulder at https://user.govoutreach.com/boulder/faq.php?cmd=shell.? ?","date":"2026-10-07","dateLabel":"Issued","cost":"$12,000","source":"https://services.arcgis.com/ePKBjXrBZ2vEEgWd/arcgis/rest/services/Construction_Permits/FeatureServer/0/query?where=PermitNum%3D%27RFG2026-00885%27&outFields=PermitNum%2COriginalAddress%2COriginalZip%2CPermitType%2CPermitWorkType%2CDescription%2CIssuedDate%2CStatusCurrent%2CEstProjectCost&f=html","group":"exterior","sentence":"All Structures must be permitted separately Total tear-off & reroof of SFD,19 squares of dimensional shingles…","costValue":12000,"lat":null,"lon":null},{"id":"RFG2026-00748","url":"https://nearbypermits.com/boulder/permit/RFG2026-00748/","address":"2075 55th St","addressUrl":"https://nearbypermits.com/boulder/address/2075-55th-st/","zip":"80301","zipUrl":"/boulder/zip/80301/","zipDerived":false,"type":"Roofing","cityType":"Roofing Replacement Permit, Roofing Replacement Permit","status":"Issued","cityStatus":"Issued","description":"Total tear-off of gravel ballast & reroof, 27 squares of EPDM on a pitch represented as.25/12. Interlocking rubber pavers to be installed on top of EPDM. All roof materials shall be installed per manufacturer?s specs. Insulation to be an average of r33. Letter from structural engineer to be provided at midroof inspection per directions provided to applicant during review. A letter from a structural engineer will be required to indicate that the roof can support the new assembly and that the new assembly will resist uplift from our high wind design standards. This letter can be provided now as part of the review or at the mid-roof inspection. The mid-roof inspections will not be passed without the letter. Mid-roof inspection is required if 1) pitch is less than 4/12 or 2) for any roof type other than asphalt shingles (regardless of pitch).. Pre-roof inspection required for all overlays. At mid-roof inspection, to ensure the safety and structural integrity of flat-roof buildings within the City of Boulder, a stamped and signed letter from a qualified engineer must be provided. The letter should certify that the installed roof membrane assembly meets all applicable building codes and safety standards, including wind speed verifications, based on an engineering review of the installation. Class A roof assembly as tested in accordance with ASTM Standard E 108 or UL Standard 790 required. 2024 City of Boulder Energy Conservation Code (COBECC) insulation requirements apply (R-33 for insulation entirely above deck, R-53 for structures with insulation in attic spaces below deck) unless the scope does not expose insulation (either above or below deck). Roofs without sufficient insulation in the cavity or on the deck and where the insulation is exposed during reroofing shall be insulated either above or below the sheathing.? At inspection, provide to building inspection staff original wrappers of materials used or applied. Provide additional information -- such as manufacturer's cut sheet for other products used - including, but not limited to, items such as flashing, valley material, sealants, fasteners, ventilation devices or features and roof jacks & penetration boots.","date":"2026-10-07","dateLabel":"Issued","cost":"$371,925","source":"https://services.arcgis.com/ePKBjXrBZ2vEEgWd/arcgis/rest/services/Construction_Permits/FeatureServer/0/query?where=PermitNum%3D%27RFG2026-00748%27&outFields=PermitNum%2COriginalAddress%2COriginalZip%2CPermitType%2CPermitWorkType%2CDescription%2CIssuedDate%2CStatusCurrent%2CEstProjectCost&f=html","group":"exterior","sentence":"Total tear-off of gravel ballast & reroof","costValue":371925,"lat":null,"lon":null},{"id":"MEC2026-01933","url":"https://nearbypermits.com/boulder/permit/MEC2026-01933/","address":"78 Benthaven Pl","addressUrl":"https://nearbypermits.com/boulder/address/78-benthaven-pl/","zip":"80305","zipUrl":"/boulder/zip/80305/","zipDerived":false,"type":"Mechanical (HVAC)","cityType":"Mechanical Permit, Mechanical HVAC/Solar","status":"Issued","cityStatus":"Issued","description":"1x Mitsubishi - GS06NA-U1 HVAC Scope: Install mini split head to upstairs room. Reinstall refrigerant pipe covering for main floor mini split head. Merge both line sets into 1 and run to outdoor unit. Recharge system to manufacturer specifications. Any electrical work required beyond a like-for-like replacement of equipment will require an electrical permit for inspection of the electrical scope.","date":"2026-10-07","dateLabel":"Issued","cost":"$3,421","source":"https://services.arcgis.com/ePKBjXrBZ2vEEgWd/arcgis/rest/services/Construction_Permits/FeatureServer/0/query?where=PermitNum%3D%27MEC2026-01933%27&outFields=PermitNum%2COriginalAddress%2COriginalZip%2CPermitType%2CPermitWorkType%2CDescription%2CIssuedDate%2CStatusCurrent%2CEstProjectCost&f=html","group":"systems","sentence":"1x Mitsubishi - GS06NA-U1 HVAC Scope: Install mini split head to upstairs room","costValue":3421,"lat":null,"lon":null},{"id":"MEC2026-01929","url":"https://nearbypermits.com/boulder/permit/MEC2026-01929/","address":"2945 16th St","addressUrl":"https://nearbypermits.com/boulder/address/2945-16th-st/","zip":"80304","zipUrl":"/boulder/zip/80304/","zipDerived":false,"type":"Mechanical (HVAC)","cityType":"Mechanical Permit, Mechanical with Electrical","status":"Issued","cityStatus":"Issued","description":"Replace 2 TON, 13 SEER AC and 97% Efficient 60K BTU Furnace, Electrical reconnect by New Age Electric. PLEASE NOTE: APPLICABLE ONLY TO SYSTEMS WITH FUEL BURNING APPLIANCES: All new plastic glued vents for fuel burning appliances must undergo pressure testing. To facilitate the inspection process, please provide photographic evidence of the pressure test directly to the assigned inspector on the day the rough mechanical inspection is scheduled. Approved tests: 10 ft water test, 5 PSI positive pressure, or Negative 5 psi air pressure test for 15 Minutes.","date":"2026-10-07","dateLabel":"Issued","cost":"$15,200","source":"https://services.arcgis.com/ePKBjXrBZ2vEEgWd/arcgis/rest/services/Construction_Permits/FeatureServer/0/query?where=PermitNum%3D%27MEC2026-01929%27&outFields=PermitNum%2COriginalAddress%2COriginalZip%2CPermitType%2CPermitWorkType%2CDescription%2CIssuedDate%2CStatusCurrent%2CEstProjectCost&f=html","group":"systems","sentence":"Replace 2 TON, 13 SEER AC and 97% Efficient 60K BTU Furnace","costValue":15200,"lat":null,"lon":null},{"id":"MEC2026-01900","url":"https://nearbypermits.com/boulder/permit/MEC2026-01900/","address":"3837 Orion Ct","addressUrl":"https://nearbypermits.com/boulder/address/3837-orion-ct/","zip":"80304","zipUrl":"/boulder/zip/80304/","zipDerived":false,"type":"Mechanical (HVAC)","cityType":"Mechanical Permit, Mechanical HVAC/Solar","status":"Issued","cityStatus":"Issued","description":"Boiler Replacement PLEASE NOTE: APPLICABLE ONLY TO SYSTEMS WITH FUEL BURNING APPLIANCES: All new plastic glued vents for fuel burning appliances must undergo pressure testing. To facilitate the inspection process, please provide photographic evidence of the pressure test directly to the assigned inspector on the day the rough mechanical inspection is scheduled. Approved tests: 10 ft water test, 5 PSI positive pressure, or Negative 5 psi air pressure test for 15 Minutes. Any electrical work required beyond a like-for-like replacement of equipment will require an electrical permit for inspection of the electrical scope.","date":"2026-10-07","dateLabel":"Issued","cost":"$37,500","source":"https://services.arcgis.com/ePKBjXrBZ2vEEgWd/arcgis/rest/services/Construction_Permits/FeatureServer/0/query?where=PermitNum%3D%27MEC2026-01900%27&outFields=PermitNum%2COriginalAddress%2COriginalZip%2CPermitType%2CPermitWorkType%2CDescription%2CIssuedDate%2CStatusCurrent%2CEstProjectCost&f=html","group":"systems","sentence":"Boiler Replacement PLEASE NOTE: APPLICABLE ONLY TO SYSTEMS WITH FUEL BURNING APPLIANCES: All new plastic…","costValue":37500,"lat":null,"lon":null},{"id":"MEC2026-01604","url":"https://nearbypermits.com/boulder/permit/MEC2026-01604/","address":"3734 Telluride Cir","addressUrl":"https://nearbypermits.com/boulder/address/3734-telluride-cir/","zip":"80305","zipUrl":"/boulder/zip/80305/","zipDerived":false,"type":"Mechanical (HVAC)","cityType":"Mechanical Permit, Mechanical with Electrical","status":"Issued","cityStatus":"Issued","description":"New 4 zone mini split heat pump and associated electrical PLEASE NOTE: APPLICABLE ONLY TO SYSTEMS WITH FUEL BURNING APPLIANCES: All new plastic glued vents for fuel burning appliances must undergo pressure testing. To facilitate the inspection process, please provide photographic evidence of the pressure test directly to the assigned inspector on the day the rough mechanical inspection is scheduled. Approved tests: 10 ft water test, 5 PSI positive pressure, or Negative 5 psi air pressure test for 15 Minutes.","date":"2026-10-07","dateLabel":"Issued","cost":"$18,948","source":"https://services.arcgis.com/ePKBjXrBZ2vEEgWd/arcgis/rest/services/Construction_Permits/FeatureServer/0/query?where=PermitNum%3D%27MEC2026-01604%27&outFields=PermitNum%2COriginalAddress%2COriginalZip%2CPermitType%2CPermitWorkType%2CDescription%2CIssuedDate%2CStatusCurrent%2CEstProjectCost&f=html","group":"systems","sentence":"New 4 zone mini split heat pump and associated electrical PLEASE NOTE: APPLICABLE ONLY TO SYSTEMS WITH FUEL…","costValue":18948,"lat":null,"lon":null},{"id":"MEC2026-01261","url":"https://nearbypermits.com/boulder/permit/MEC2026-01261/","address":"826 Maxwell Ave","addressUrl":"https://nearbypermits.com/boulder/address/826-maxwell-ave/","zip":"80304","zipUrl":"/boulder/zip/80304/","zipDerived":false,"type":"Mechanical (HVAC)","cityType":"Mechanical Permit, Mechanical with Electrical","status":"Issued","cityStatus":"Issued","description":"Installing ductless heat pump mini split system: 1-Mitsubishi Electric MXZ-SM48NLHZ - Heat Pump 5-Indoor wall mounted units 1-New circuit for heat pump Historic approval HIS2026-00258. PLEASE NOTE: APPLICABLE ONLY TO SYSTEMS WITH FUEL BURNING APPLIANCES: All new plastic glued vents for fuel burning appliances must undergo pressure testing. To facilitate the inspection process, please provide photographic evidence of the pressure test directly to the assigned inspector on the day the rough mechanical inspection is scheduled. Approved tests: 10 ft water test, 5 PSI positive pressure, or Negative 5 psi air pressure test for 15 Minutes.","date":"2026-10-07","dateLabel":"Issued","cost":"$29,962","source":"https://services.arcgis.com/ePKBjXrBZ2vEEgWd/arcgis/rest/services/Construction_Permits/FeatureServer/0/query?where=PermitNum%3D%27MEC2026-01261%27&outFields=PermitNum%2COriginalAddress%2COriginalZip%2CPermitType%2CPermitWorkType%2CDescription%2CIssuedDate%2CStatusCurrent%2CEstProjectCost&f=html","group":"systems","sentence":"Installing ductless heat pump mini split system: 1-Mitsubishi Electric MXZ-SM48NLHZ - Heat Pump 5-Indoor wall…","costValue":29962,"lat":null,"lon":null},{"id":"ELE2026-01107","url":"https://nearbypermits.com/boulder/permit/ELE2026-01107/","address":"1047 13th St 4","addressUrl":"https://nearbypermits.com/boulder/address/1047-13th-st-4/","zip":"80302","zipUrl":"/boulder/zip/80302/","zipDerived":false,"type":"Electrical","cityType":"Electrical Permit, Electrical Permit","status":"Issued","cityStatus":"Issued","description":"*Re-instatement permit for ELE2024-00811* New 200amp service to structure.","date":"2026-10-07","dateLabel":"Issued","cost":"$6,200","source":"https://services.arcgis.com/ePKBjXrBZ2vEEgWd/arcgis/rest/services/Construction_Permits/FeatureServer/0/query?where=PermitNum%3D%27ELE2026-01107%27&outFields=PermitNum%2COriginalAddress%2COriginalZip%2CPermitType%2CPermitWorkType%2CDescription%2CIssuedDate%2CStatusCurrent%2CEstProjectCost&f=html","group":"systems","sentence":"*Re-instatement permit for ELE2024-00811* New 200amp service to structure","costValue":6200,"lat":null,"lon":null},{"id":"ELE2026-01089","url":"https://nearbypermits.com/boulder/permit/ELE2026-01089/","address":"730 31st St","addressUrl":"https://nearbypermits.com/boulder/address/730-31st-st/","zip":"80303","zipUrl":"/boulder/zip/80303/","zipDerived":false,"type":"Electrical","cityType":"Electrical Permit, Electrical Permit","status":"Issued","cityStatus":"Issued","description":"Upgrade the electrical service from 100 amps to 200 amps","date":"2026-10-07","dateLabel":"Issued","cost":"$4,300","source":"https://services.arcgis.com/ePKBjXrBZ2vEEgWd/arcgis/rest/services/Construction_Permits/FeatureServer/0/query?where=PermitNum%3D%27ELE2026-01089%27&outFields=PermitNum%2COriginalAddress%2COriginalZip%2CPermitType%2CPermitWorkType%2CDescription%2CIssuedDate%2CStatusCurrent%2CEstProjectCost&f=html","group":"systems","sentence":"Upgrade the electrical service from 100 amps to 200 amps","costValue":4300,"lat":null,"lon":null},{"id":"ELE2026-01088","url":"https://nearbypermits.com/boulder/permit/ELE2026-01088/","address":"1009 Tantra Park Cir","addressUrl":"https://nearbypermits.com/boulder/address/1009-tantra-park-cir/","zip":"80305","zipUrl":"/boulder/zip/80305/","zipDerived":false,"type":"Electrical","cityType":"Electrical Permit, Electrical Permit","status":"Issued","cityStatus":"Issued","description":"new 50a dedicated circuit for range outlet in existing kitchen to replace current range outlet","date":"2026-10-07","dateLabel":"Issued","cost":"$3,615","source":"https://services.arcgis.com/ePKBjXrBZ2vEEgWd/arcgis/rest/services/Construction_Permits/FeatureServer/0/query?where=PermitNum%3D%27ELE2026-01088%27&outFields=PermitNum%2COriginalAddress%2COriginalZip%2CPermitType%2CPermitWorkType%2CDescription%2CIssuedDate%2CStatusCurrent%2CEstProjectCost&f=html","group":"systems","sentence":"New 50a dedicated circuit for range outlet in existing kitchen to replace current range outlet","costValue":3615,"lat":null,"lon":null},{"id":"BLD-SFD2026-00452","url":"https://nearbypermits.com/boulder/permit/BLD-SFD2026-00452/","address":"885 35th St","addressUrl":"https://nearbypermits.com/boulder/address/885-35th-st/","zip":"80303","zipUrl":"/boulder/zip/80303/","zipDerived":false,"type":"Addition","cityType":"Building Permit - Single Family Detached Dwelling, Addition and Alteration","status":"Issued","cityStatus":"Issued","description":"The proposed project at 885 35th street consists of a 325-square-foot interior renovation to the existing 1,312-square-foot, one-story single-family residence, including a kitchen remodel and the removal of an existing structural wall. The project also includes a 480 sqft (size of foundation), 462 sqft (outside of framing) modular addition on the rear of the home. This permit application is limited to the site-built work associated with the modular addition, including the foundation and the structural connections between the modular unit and the existing residence. While the site plan depicts a proposed detached accessory dwelling unit (adu), the ADU is being submitted under a separate permit application and is not part of this review. Both projects are located on the same property.","date":"2026-10-07","dateLabel":"Issued","cost":"$175,000","source":"https://services.arcgis.com/ePKBjXrBZ2vEEgWd/arcgis/rest/services/Construction_Permits/FeatureServer/0/query?where=PermitNum%3D%27BLD-SFD2026-00452%27&outFields=PermitNum%2COriginalAddress%2COriginalZip%2CPermitType%2CPermitWorkType%2CDescription%2CIssuedDate%2CStatusCurrent%2CEstProjectCost&f=html","group":"alter","sentence":"The proposed project at 885 35th street consists of a 325-square-foot interior renovation to the existing…","costValue":175000,"lat":null,"lon":null},{"id":"BLD-SFD2026-00072","url":"https://nearbypermits.com/boulder/permit/BLD-SFD2026-00072/","address":"1002 Rose Hill Dr","addressUrl":"https://nearbypermits.com/boulder/address/1002-rose-hill-dr/","zip":"80302","zipUrl":"/boulder/zip/80302/","zipDerived":false,"type":"Alteration or repair","cityType":"Building Permit - Single Family Detached Dwelling, Alteration","status":"Issued","cityStatus":"Issued","description":"Remodel of existing residential basement to include a new attached accessory dwelling unit (630 sq ft). Scope to include small change to exterior framing of a bump out on main floor on south side of dwelling. Change of Scope 10/1/26 to include the reconfiguration of a curved wall on the south side of the main level and re-framed/squared to match the exiting upper-level wall framing.","date":"2026-10-07","dateLabel":"Issued","cost":"$85,400","source":"https://services.arcgis.com/ePKBjXrBZ2vEEgWd/arcgis/rest/services/Construction_Permits/FeatureServer/0/query?where=PermitNum%3D%27BLD-SFD2026-00072%27&outFields=PermitNum%2COriginalAddress%2COriginalZip%2CPermitType%2CPermitWorkType%2CDescription%2CIssuedDate%2CStatusCurrent%2CEstProjectCost&f=html","group":"alter","sentence":"Remodel of existing residential basement to include a new attached accessory dwelling unit (630 sq ft)","costValue":85400,"lat":null,"lon":null},{"id":"BLD-NRE2026-00116","url":"https://nearbypermits.com/boulder/permit/BLD-NRE2026-00116/","address":"250 Arapahoe Ave","addressUrl":"https://nearbypermits.com/boulder/address/250-arapahoe-ave/","zip":"80302","zipUrl":"/boulder/zip/80302/","zipDerived":false,"type":"Alteration or repair","cityType":"Building Permit - Non-Residential, Alteration","status":"Finished","cityStatus":"Closed","description":"Case for the purposes of invoicing fees associated with annexation LUR2024-00052.","date":"2026-10-07","dateLabel":"Issued","cost":"","source":"https://services.arcgis.com/ePKBjXrBZ2vEEgWd/arcgis/rest/services/Construction_Permits/FeatureServer/0/query?where=PermitNum%3D%27BLD-NRE2026-00116%27&outFields=PermitNum%2COriginalAddress%2COriginalZip%2CPermitType%2CPermitWorkType%2CDescription%2CIssuedDate%2CStatusCurrent%2CEstProjectCost&f=html","group":"alter","sentence":"Case for the purposes of invoicing fees associated with annexation LUR2024-00052","costValue":null,"lat":null,"lon":null},{"id":"BLD-NRE2026-00109","url":"https://nearbypermits.com/boulder/permit/BLD-NRE2026-00109/","address":"6007 Oreg Ave","addressUrl":"https://nearbypermits.com/boulder/address/6007-oreg-ave/","zip":"80303","zipUrl":"/boulder/zip/80303/","zipDerived":false,"type":"Alteration or repair","cityType":"Building Permit - Non-Residential, Addition and Alteration","status":"Issued","cityStatus":"Issued","description":"*For site work only associated with TEC2026-00031 and ADR2026-00014 39,000SF site project consisting of landscaping, irrigation, storm drainage, and site concrete. Fencing, sound barrier wall, and shade structures / pavilion steel structure to be permitted separately under accessory and fence / wall permits.","date":"2026-10-07","dateLabel":"Issued","cost":"$443,000","source":"https://services.arcgis.com/ePKBjXrBZ2vEEgWd/arcgis/rest/services/Construction_Permits/FeatureServer/0/query?where=PermitNum%3D%27BLD-NRE2026-00109%27&outFields=PermitNum%2COriginalAddress%2COriginalZip%2CPermitType%2CPermitWorkType%2CDescription%2CIssuedDate%2CStatusCurrent%2CEstProjectCost&f=html","group":"alter","sentence":"*For site work only associated with TEC2026-00031 and ADR2026-00014 39,000SF site project consisting of…","costValue":443000,"lat":null,"lon":null},{"id":"BLD-NRE2026-00106","url":"https://nearbypermits.com/boulder/permit/BLD-NRE2026-00106/","address":"2032 14th St","addressUrl":"https://nearbypermits.com/boulder/address/2032-14th-st/","zip":"80302","zipUrl":"/boulder/zip/80302/","zipDerived":false,"type":"Alteration or repair","cityType":"Building Permit - Non-Residential, Alteration","status":"Issued","cityStatus":"Issued","description":"Accessibility improvement of existing space to provide new accessible restroom. No change in square footage. No change in use or occupancy. Change of Scope 10/1/26 scope to include permitting a walk-in cooler.","date":"2026-10-07","dateLabel":"Issued","cost":"$64,100","source":"https://services.arcgis.com/ePKBjXrBZ2vEEgWd/arcgis/rest/services/Construction_Permits/FeatureServer/0/query?where=PermitNum%3D%27BLD-NRE2026-00106%27&outFields=PermitNum%2COriginalAddress%2COriginalZip%2CPermitType%2CPermitWorkType%2CDescription%2CIssuedDate%2CStatusCurrent%2CEstProjectCost&f=html","group":"alter","sentence":"Accessibility improvement of existing space to provide new accessible restroom","costValue":64100,"lat":null,"lon":null}],"source":"https://www.arcgis.com/home/item.html?id=e3ff6248e4a547bcba31025d2c5c9fee","source_agency":"Boulder Planning and Development Services","source_license":{"name":"CC0 1.0","url":"https://creativecommons.org/publicdomain/zero/1.0/","terms_url":"https://creativecommons.org/publicdomain/zero/1.0/"},"page_url":"https://nearbypermits.com/boulder/","see_more":"Newest permits in Boulder, and its busiest ZIP codes: https://nearbypermits.com/boulder/"}