Skip map
Map preview
Open mapBack to list
- Searched address
- Addition or alteration
- Electrical, plumbing, HVAC
- Roof, fence, sign, facade
- Paperwork or other
560 Bayview Blvd
Baltimore, MD 21224
The biggest project within a quarter mile since May 1: a $345,718 project at 333 Cassell Dr, permitted Jun 25.
Four permits on record here. The newest, May 21: Install compete fire alarm scope based on the BOM in the submittals 4 Wall-Mount. Within a quarter mile, the city has issued 23 more permits since May 1.
Within
Since
Here4 permits · 560 Bayview Blvd
-
May 21$16,000
-
Mar 18$19,000
-
Mar 2$10,000
-
Level II interior alterations ------- conversion of ground floor suite 1 from warm shell to restaurantAlteration or repairJan 20$760,000
Sort
This block250 to 1,000 ft · 13 permits
-
Permit, no description from the city639 Rappolla St · 1,000 ft W · OtherOct 6$65,000
-
Permit, no description from the city620 Tolna St · 650 ft W · OtherOct 5$10,000
-
19 Circuits457 Anglesea St · 990 ft NE · ElectricalSep 17$150
-
Installing gas test for Furnace, stove, water heater and dryer605 Rappolla St · 970 ft W · PlumbingAug 28$4,500
-
Replacing existing 100kw generator set and 3 circuits as per code5710 Eastern Ave · 840 ft NE · ElectricalAug 14$1,000
-
Non illuminated sign panel mounted to fa ade5525 Eastern Ave · 320 ft N · SignAug 10$500
-
SCOPE OF WORK (to include work in SWO) ---- ADDITION ----- - removing existing Rear Addition and REPLACE with…605 Rappolla St · 970 ft W · AdditionJul 10$6,000
-
1 kitchen sink 1 garbage disposal 1 washer box 1 electric water heater 2 toilets 2 lavatories 1 bathtub 1…457 Anglesea St · 990 ft NE · PlumbingJun 30$2,500
-
Heat pump AC 2.5 ton Ductwork 2-bathroom exhaust fan 1 dryer exhaust fan457 Anglesea St · 990 ft NE · Mechanical (HVAC)Jun 30$2,300
-
1 Sub panel 125 amps, 28 receptacles457 Anglesea St · 990 ft NE · ElectricalJun 30$950
-
Permit, no description from the city507 Savage St · 780 ft W · OtherJun 16$10,291
-
Modify Existing Fire Alarm Permit5525 Eastern Ave · 320 ft N · Fire systemsMay 20$6,750
-
Low voltage permit for STE 109: 35 Cameras cat6 5 WiFi Access Point cat 6 2 Door access control 18/4 22/6 +…5525 Eastern Ave · 320 ft N · ElectricalMay 19$1,500
Within a quarter mile1,000 ft to ¼ mi · 10 permits
-
Remove and replace shared rear roof in between 622 Rappolla St and 624*622 Rappolla St · 0.21 mi W · Alteration or repairSep 9$6,500
-
Remove and replace rear roof between 624 Rappolla St as per Design Professionals drawing (See Attacment) as…624 Rappolla St · 0.21 mi W · RoofingAug 27$6,500
-
Level concrete steps n front of home714 Rappolla St · 0.23 mi SW · OtherAug 5$300
-
Replace existing 2.5 ton ac and 70k btu furnace442 Bonsal St · 0.22 mi NE · Mechanical (HVAC)Aug 4$10,024
-
Waste and water reconstruction electric hot water heater5021 Eastern Ave · 0.22 mi W · ElectricalJun 29$1,000
-
1 Gas stove 120,000 btu432 Bonsal St · 0.23 mi NE · PlumbingJun 25$1,000
-
To install 645 lv data/voice devices in interior alterations within the triad technology center333 Cassell Dr · 0.23 mi NW · ElectricalJun 25$345,718
-
Replacement of 40 Gal Natural Gas 40,000 BTU water heater - expansion tank - ball valve - drain pan626 Rappolla St · 0.21 mi W · PlumbingJun 2$3,600
-
Install 200 amp service, 3 circuits432 Bonsal St · 0.23 mi NE · ElectricalMay 28$4,200
-
Permit, no description from the city432 Bonsal St · 0.23 mi NE · OtherMay 11$5,500
More on this streetBayview Blvd · 4 other addresses with permits
- 517 Bayview Blvd newest permit Aug 20, 2025
- 509 Bayview Blvd newest permit Nov 26, 2025
- 503 Bayview Blvd 503 Highlandtown Maryland 21224-2726 newest permit Oct 30, 2024
- 251 Bayview Blvd newest permit Sep 22, 2026
Baltimore Department of Housing and Community Development updated its data Oct 8, 2026. We checked it Oct 8, 03:09 UTC. See the city's official records (City of Baltimore, CC BY 3.0).
At this address: every permit the city holds. Nearby: permits from the last two years, from our copy of the city's data.
For agents and scripts: This page as Markdown · JSON · Nearby as JSON · MCP tool permits_near